Quality begins from the ground up.
Preparing your surface is the most critical task of any tile or stone installation. Custom Building Products offers you one source for the needs of virtually any job.
The foundation of precise tile and stone setting.
Whatever the application, CUSTOM® offers the broadest line of tile and stone setting materials in the industry to give the exact performance your job demands.
Tile grout with dependable performance and color.
Look for tile grout with rock-solid durability, consistency and the largest color palette with Custom. Our grouts are easy to work with yet deliver hard, dense joints.
Care & Maintenance
Stains can RUIN Stone & Tile.Protect Yours Now!
Stains on stone, tile or grout happen easily - and can leave permanent stains. Protect your surface against both oil-based and water-based stains with the right sealer.
Professional Solutions for Professional Results
Offering the largest selection of Sealers, Cleaners, Problem Solvers, Grout Colorant and Stone Restoration products, we provide professionals with the right tools and solutions; making us the #1 Contractor Preferred Manufacturer of Sealers and Cleaners.
CustomTech Flooring Prep
CustomTech – the industry’s leading collection of technologically-superior, easy-to-use, professional grade subfloor preparation products designed for all types of floor coverings.
Tools & Accessories
Precision demands the best.
SuperiorBilt® Tools are professionally preferred for tile, stone and floor covering installations.
Products : Surface Prep : Waterproofing Membranes & Underlayments : RedGard® SpeedCoat® Waterproofing Membrane
American National Standards Institute (ANSI) ANSI A108.01, A108.13, A118.10
American National Standards for the Installation of Ceramic Tile ASTM International (ASTM)
Tile Council of North America (TCNA) TCNA Handbook for Ceramic Tile Installation, TCNA Method EJ171
RedGard®SpeedCoat has tested and complies with Uniform Plumbing Code and International Plumbing Code standards for use as a shower pan liner per IAPMO Research and Testing, Inc., File No. 4244. RedGard®SpeedCoat has tested and complies with International Building Code (IBC), International Residential Code (IRC) and International Plumbing Code (IPC) standards for water resistance per ICC Evaluation Service, PMG-1389.
Installation must comply with the requirements of all applicable local, state and federal code jurisdictions.
Reactive polymers with inorganic fillers and pigments.
Custom® Building Products is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product may contribute to LEED® certification.
USE CHEMICAL-RESISTANT GLOVES, such as nitrile, when handling product.
Wet areas must have proper sloping to drains. All surfaces must be structurally sound, clean, dry and free from contaminants that would prevent a good bond. Newly prepared concrete must be troweled smooth and textured to a fine broom finish and cured for 24 hours. All cracks must be filled. All cracks greater than 1/8" wide should be prefilled with mortar, SpeedFinish(tm) Patching and Finishing Compound or CUSTOM 100% Silicone Sealant before beginning the waterproofing application.
Do not bridge joints designed to experience movement. Carry these types of joints through the tile work. Follow TCNA, EJ171.
Wear impervious gloves and eye protection while using this product. Avoid contact with eyes or prolonged contact with skin. Wash thoroughly after handling. If eye contact occurs, rinse cautiously with water for several minutes, remove contact lenses if easy to do: continue rinsing. Immediately seek medical advice if symptoms are significant or persist. Do not take internally. KEEP OUT OF REACH OF CHILDREN.
SHOWER RECEPTORS INSTALLATION
Mortar Bed over Framed Structures – B414
Cement Backerboard Walls – B415
Surface Bonded Waterproofing – B421
Download the illustrated installation details by clicking on the link above or go to mantelapp.comTSD, select “Tile” as the installation type and select the appropriate illustrated TCNA detail by number (example: B414).
For General Waterproofing, apply one continuous coat of SpeedCoat at a rate of 220 sq ft per gallon, to surface with a 1/4" smooth texture roller. Inspect and repair any voids in coating before installation of tile. Rough surfaces will reduce coverage rate, apply at a rate of 130 sq ft per gallon.
RedGard SpeedCoat at Drains
Drains should have a clamping ring with open weep holes for thin-set application. Apply the RedGard SpeedCoat membrane to the bottom of the flange. The drain should be fully supported, without movement, and should be even with the plane of the substrate. Apply the RedGard SpeedCoat membrane around drain and embed Waterproofing Reinforcing Tape into the membrane, making sure it does not obstruct the drainage weep holes. Alternatively, fill the gap between the substrate and the drain flange with CUSTOM 100% Silicone Sealant. After the sealant is tacky to the touch, approximately 10 minutes, apply an initial coat of the membrane. When dry, apply an additional coat of the membrane. NOTE: Apply membrane over Silicone Caulk within 3 hours. Membrane will not adhere to silicone when applied on next day. After curing, clamp the upper flange onto the membrane and tighten. Use a rapid curing urethane caulk around the flange where the membrane and the upper flange make contact. A toilet flange can be treated in much the same manner.
Applying RedGard® SpeedCoat Waterproof Membrane (ANSI 118.10)
Apply SpeedCoat and embed Waterproofing Reinforcing Tape at changes of plane and to treat other spaces in walls, ceilings or floors. Alternately, use CUSTOM 100% Silicone Sealant in place of fabric. Apply SpeedCoat membrane over silicone when it has become tacky.
SMOOTH SURFACES: Stir product by hand before using. Do not dilute. Apply RedGard® SpeedCoat using a 1/4" (6mm) smooth textured synthetic roller or flat steel trowel over the entire area to be treated. Apply two coats at 6 mils each over a 110 ft2 area for proper coverage of an IAPMO shower pan creating a continuous, even film with overlapping strokes. Inspect the film for integrity and fill any voids or pinholes with additional material.
ROUGH TEXTURED SURFACES will result in a reduced coverage rate. To meet IAMPO requirements for shower pans, use a steel trowel or a ½” nap (12mm) roller and apply two coats at 6 mils forming a continuous, even film at a rate of 130 sq ft per gallon for each coat. Inspect the film for integrity and fill any voids or pinholes with additional material. To achieve maximum coverage, smooth the surface with SpeedFinish™ Patching & Finishing Compound prior to applying membrane.
Each coat of RedGard® SpeedCoat is dry to the touch in typically 1hr. Product does NOT change colors as it dries. After the second coat is applied and cured, the application area can be flood tested, typically 1 hr later. Ambient conditions can affect dry time.
Install tile or stone with a Custom® Building Products polymer•modified mortar that meets ANSI A118.4 or A118.15 standards. Use epoxy adhesive meeting ANSI A118.3 for moisture sensitive tiles or where chemical resistance is required.
Clean tools and hands with isopropyl alcohol (i.e. rubbing alcohol) before the material dries.
Properly installed product requires no special maintenance. Do not use as a wear surface.
Obtain the applicable LIMITED PRODUCT WARRANTY at mantelapp.com/product-warranty or send a written request to Custom Building Products, Inc., Five Concourse Parkway, Atlanta, GA 30328, USA. Manufactured under the authority of Custom Building Products, Inc. © 2017 Quikrete International, Inc.
*Note that monolithic coats are required to waterproof and two coats are only required for IAPMO shower pan applications on floors, coves and curbs. Chart for estimating purposes. Coverage may vary based on installation practices and jobsite conditions.
CUSTOM BUILDING PRODUCTS
Mailing Address Custom Building Products 7711 Center Ave. Ste 500 Huntington Beach, CA 92647
© 2019 新乐彩app All Rights